cre8audio Function Junctionn analog modulator

According to the user manual, “Function Junction is a modulation hub combining four independent sections into a single intertwined module that offers much more than the sum of its parts. Although a sum of its parts is one of its best features!” I think what the ultra-serious manual writer was trying to say is that Function Junction can do more than a ton of things. In fact, it’s downright impressive what’s possible with this lovely module.

specificatie

• Width = 16hp
• Depth = 30mm
• Power draw
  • 130mA when running +12V rail
  • 70mA when running -12V
• ADSR / Envelope facts
  • Fully analog Pittsburgh Modular Synthesizers developed 4 stage ADSR circuit with independent Attack, Decay, Sustain and Release controls.
  • Voltage output range 0V - 10V
  • “Long” button doubles the length of the envelope attack, decay, and release times
  • “Loop” button enables/disables envelope cycling. The SUSTAIN KNOB and RELEASE KNOB are used to adjust the time it takes to loop.
  • “A LOOP JACK” - Enables/disable loop mode. An external gate signal will flip the state of the loop mode. If loop mode is on, the gate will turn loop mode off. If loop mode is off, the external gate will turn loop mode on.
• Function Generator facts
  • Function Generator can be used as an envelope generator, a voltage controlled LFO, a slew generator, a gate signal delay, envelope follower, a clock source, voltage controlled clock divider, complex modulation source, and more
  • Voltage output range +/-5V
  • ATTACK KNOB - Attack duration control knob.
  • DECAY KNOB - Decay duration control knob.
  • CURVE KNOB - Attack and decay response curve. Exponential (full left), Linear (12 o’clock), Logarithmic (full right)
  • MOD KNOB - Modulation input (F MOD JACK) attenuverter knob.
  • MOD BUTTON - Assign Modulation input (F MOD JACK) to attack, decay, or both.
  • LOOP BUTTON - Enable/Disable loop mode.
  • LOOP BUTTON (2nd FUNCTION) - Press and hold MOD BUTTON then press LOOP BUTTON to assign A LOOP JACK destination to ADSR or function generator.
  • SUSTAIN BUTTON - Enable/Disable sustain mode.
  • F IN JACK - Function Generator trigger/gate input gate jack.
  • F MOD JACK - Function Generator modulation input jack.
  • F OUT JACK - Function Generator output jack.
  • F TRIG JACK - Function Generator end of decay trigger output jack. A trigger is output at the end of the decay stage.
• LFO facts
  • Triangle and Square LFO outs
  • Dedicated rate knob
  • LFO output voltage +/-8V
• Mixer facts
  • 3 channel attenuverting mixer with OR circuit
  • Mixer can be split into 3 independent attenuverters, one two-channel mixer, and one attenuverter, or a three-channel mixer
  • OUTPUT 1 KNOB - Channel 1 input (1A JACK) attenuverter knob.
  • OUTPUT 2 KNOB - Channel 2 input (2F JACK) attenuverter knob.
  • OUTPUT 3 KNOB - Channel 3 input (3L JACK) attenuverter knob.
  • 1A JACK - Channel 1 input jack. Normaled to ADSR output.
  • 2F JACK - Channel 2 input jack. Normaled to function generator output.
  • 3L JACK - Channel 3 input jack. Normaled to LFO output.
  • +OR JACK - Analog logic output jack.
    • OR circuit outputs the current highest voltage value of any of the voltages output by the mixer
  • 1 OUT JACK - Channel 1 breakout output.
  • 2 OUT JACK - Channel 2 breakout output.
  • MIX JACK - Mixer output.

Product Homepage